A quote for commercial pool furniture is priced from the frame and finish of each piece and from its seat, which can be a sling, straps or a cushion. How many pieces fit depends on the deck. The CDC’s 2024 Model Aquatic Health Code calls for a perimeter deck at least 4 feet wide and unobstructed around a pool, and says deck furniture has to be placed outside the circulation path.
This page covers pools at hotels, HOAs, apartment communities, country clubs and municipal parks, with sources checked October 26, 2026. The buying guide to commercial outdoor furniture compares materials and lists umbrella base weights.
How much of the deck can furniture use?
The Model Aquatic Health Code (MAHC) is guidance from the Centers for Disease Control and Prevention that state and local health agencies can adopt, so ask the local health department which pool code it enforces. The 2024 edition sets these limits:
| Rule | MAHC section |
|---|---|
| The perimeter deck, the strip of deck around the pool, is 4 feet wide minimum in unobstructed width | 4.8.1.5.1.1 |
| 4 feet of clearance from the pool edge to fencing or another obstruction, for lifeguards | 4.8.1.1.1.1 |
| 4 feet of unobstructed deck around lifeguard stands, diving equipment, ADA access equipment and columns | 4.8.1.5.2.1 |
| Deck furniture stays out of the circulation path | 4.8.1.5.3.2 |
| The perimeter deck is kept free of obstructions, including patron seating | 5.6.9.3.1 |
| No glass furniture | 5.6.9.2.2 |
| Furniture does not block access to rinse showers | 5.10.4.3.3 |
Which accessibility rules affect the layout?
Section 4.8.1.5.3.1 of the MAHC calls for a circulation path that conforms with ADA requirements for an accessible route. Section 403.5.1 of the 2010 ADA Standards sets the clear width of an accessible route at 36 inches minimum, so leave that width between rows of chaise lounges wherever the route runs.
Section 242.2 requires at least two accessible means of entry into a swimming pool, or one for a pool with less than 300 linear feet of wall if it is a pool lift or a sloped entry. The deck beside each has to stay clear. A pool lift needs a clear deck space 36 inches wide and 48 inches long beside the seat, on the side away from the water, under section 1009.2.3. A transfer wall, a low wall a swimmer sits on and slides across into the water, needs 60 by 60 inches of clear deck at its base under section 1009.4.1. Mark these spaces on the deck plan before counting chaises. Tables at a pool bar follow the guide to accessible tables, counters and benches.
Frames and finishes near chlorine and salt water
Powder coating is a dry paint fused to metal with heat. Anodizing is a finish formed in the surface of the aluminum itself. Frankford Umbrellas, an umbrella maker, says aluminum does not rust but does oxidize, and that long submersion in salt water or chemically treated pool water can whiten and pit it. It says a deep scratch in powder coating exposes bare aluminum, recommends anodized or brushed finishes for poles that stand in a pool, and advises rinsing them with fresh water several times a week. That guidance is written for umbrella poles, so for furniture on a sun shelf, the shallow ledge inside some pools, ask the maker whether the frame is rated for standing in water.
The Fenestration and Glazing Industry Alliance (FGIA) publishes AAMA 2603, 2604 and 2605, voluntary specifications for factory-applied organic coatings on architectural aluminum, which an FGIA staff liaison calls the good, better and best categories of aluminum finishes. FGIA released new editions in May 2026. If a specification names one for furniture, ask for a test report that names the specification and edition.
HDPE lumber is high-density polyethylene, a solid plastic milled into boards. POLYWOOD, an HDPE furniture maker, says its pigments and UV inhibitors run through the material, so it needs no painting. For tanning ledges it makes a separate line in linear low-density polyethylene that it says can stay in the water year-round without damage from sun, salt or chlorine, and it warns that this furniture may float in water deeper than 9 inches.
Standards for resin chaises and chairs
ASTM International publishes performance standards for plastic furniture used outdoors, each with tests for weathering, impact and static load and a test base that simulates a wet pool deck. ASTM F1988-99(2026) covers plastic chaise lounges with adjustable backs in Class A (residential) and Class B (nonresidential). ASTM F1838-19(2025) covers plastic chairs in the same two classes and excludes chaises. ASTM F1858-98(2026) covers plastic chairs that recline. ASTM withdrew F1561, the older chair standard, in 2019 and lists F1838 as its replacement. All of these are written for plastic furniture, so for an aluminum or HDPE chaise ask which test it was built to. The guide to standards for commercial furniture covers the rest.
Slings, straps and cushions
A sling is one piece of fabric stretched across the frame as the seat. Straps are bands wrapped across the frame. Ask for the seat’s warranty separately from the frame’s. Oxford Garden, an outdoor furniture maker, warrants its dual-layer strap for one year against structural failure and major discoloration.
The federal flammability standard for upholstered furniture, 16 CFR part 1640, defines upholstered furniture as seating intended for indoor use. Minutes of a March 3, 2015 advisory council meeting of California’s home furnishings bureau record a bureau lab supervisor’s statement that furniture used solely outdoors is not subject to Technical Bulletin 117-2013, the smolder test the federal rule adopts. Neither rule applies to cushions on furniture made only for outdoor use. If the same seating will also go indoors, such as in a clubhouse, ask whether it carries the federal compliance label.
Quick-dry foam is an open-cell foam that lets water run through it. Cane-line, a furniture maker, says its quick-dry cushions are dry within an hour after a rain shower. Section 5.6.9.3.7 of the MAHC says wet areas shall not have absorbent materials that cannot be removed for daily cleaning and disinfection, which is a reason to ask for cushions that come off the frame.
Umbrellas at the pool
Frankford says its umbrellas are not designed or warranted for continuous submersion in a pool sleeve, and that submerging the frame voids its three-year frame finish warranty. For a pool ledge it recommends a two-piece center pole, so the lower section can be replaced, and a bar-height lower pole about 10 inches longer to make up for the depth of the sleeve. ASTM F3512 tests the wind safety of market umbrellas, and its scope names resort pools.
Spec checklist for a pool furniture quote
Copy this table into the quote request’s notes or an email and fill in the right-hand column.
| Item | What to state | Your project |
|---|---|---|
| Pieces | Chaises, chairs, side tables, dining tables, umbrellas and bases, with a count for each | |
| Pool | Chlorine or salt water, indoor or outdoor | |
| In-pool pieces | Furniture or umbrellas on a sun shelf, and the water depth | |
| Frame | Powder-coated or anodized aluminum, HDPE lumber or plastic resin, and the color | |
| Finish | Any AAMA coating specification and edition, and the finish warranty wanted | |
| Seat | Sling, strap or cushion, with fabric name and color | |
| Cushions | Quick-dry foam, removable covers, ties | |
| Standards | ASTM F1988 Class B for plastic chaises, F1838 Class B for plastic chairs, an F3512 rating for umbrellas | |
| Deck plan | The 4-foot perimeter deck, the 36-inch route, and clear space at the pool lift | |
| Storage | Stacking height, wheels on chaises, off-season storage | |
| Delivery | ZIP code, access to the deck, date the pool opens |
For a hotel or resort pool, start a quote request with the project type set to Hotel or resort, and for an HOA, apartment community, club or municipal pool, change the project type on the form.